Bullnose Aquarium Volume Calculator

1. Overall Length: Measure the overall inside length from the flat end to the farthest point of the curved end.
2. Width: Measure the inside width across the flat sides.
3. Bullnose Radius: Measure from the center of the curve to the curved glass. When the curve spans the full width, the radius is half the inside width.
4. Height: Measure from the inside bottom of the tank up to the water line.

Measure inside dimensions, glass to glass, inside any frame or trim, and measure each dimension twice.

• If both ends of the tank are curved, use the Round End calculator instead.

The calculator adds a rectangular body (overall length minus the radius, times the width) to a half-cylinder end of the radius you enter. When the curve spans the full width of the tank the radius is half the width, as in the worked example below: 14 ÷ 2 = 7 inches.

This formula calculates the interior volume in cubic units matching your input measurements. If you measure in inches, the result is cubic inches; divide by 231 to convert to US gallons, or multiply gallons by 3.785 for liters. If you measure in centimeters, the result is cubic centimeters; divide by 1,000 for liters.

Consider a bullnose aquarium with the following inside dimensions: 30-inch overall length, 14-inch width, 7-inch radius, 16 inches tall.

1. Rectangular section: (30 - 7) × 14 × 16 = 23 × 14 × 16 = 5,152 cubic inches
2. Half-cylinder cap: (π × 7² × 16) ÷ 2 = 1,231.50 cubic inches
3. Total volume: 5,152 + 1,231.50 = 6,383.50 cubic inches
4. Convert to gallons: 6,383.50 ÷ 231 = 27.64 US gallons
5. Convert to liters: 27.64 × 3.785 = 104.62 liters

Result: This bullnose aquarium holds approximately 27.64 US gallons (104.62 liters) of water when filled to the measured height.

Fill Height

The calculator above assumes you fill the tank to the full measured height. In practice, most aquarists keep the water level 1–2 inches below the rim to prevent overflow during water changes, when adding hands and equipment, or if fish splash. Use the fill height adjustment toggle in the calculator to enter your actual water line height for a more realistic volume estimate.

For tanks with open-top (rimless) designs, the gap between water surface and glass top is especially important to track. A 2-inch gap on a 20-inch tall tank reduces effective volume by 10%, which is significant for medication dosing.

Substrate Displacement

Gravel, sand, and planted substrates occupy space that would otherwise hold water. A 2-inch layer of gravel in a standard rectangular tank displaces roughly 5–8% of the total tank volume. Use the substrate displacement toggle in the calculator to subtract this volume from your water capacity estimate.

Rock and Decoration Displacement

Large rocks, driftwood, and dense decorations also displace water, which this calculator does not subtract. Use the aquarium displacement calculator to estimate how much.

For how glass thickness reduces interior volume on your specific tank size, see the glass thickness and volume loss guide.

The calculator displays estimated water weight for both freshwater (8.34 lbs per gallon) and saltwater (8.55 lbs per gallon at 1.025 specific gravity). These estimates help you determine whether your floor and stand can safely support the filled tank, substrate, and equipment combined.

Water weight estimates are approximate and based on standard conditions. Freshwater weight assumes pure water at 62 °F (16.7 °C) with a density of 8.34 lbs/gal (1.0 kg/L). Saltwater weight assumes a specific gravity of 1.025, typical of reef aquariums. Actual weight may vary depending on water temperature, salinity, dissolved minerals, and substrate displacement. Always verify that your aquarium stand and floor can support the total weight of the filled tank, substrate, equipment, and decorations before filling.

• Measuring outside dimensions: Glass or acrylic thickness ranges from 3 mm to 19 mm per panel. Using outside dimensions overstates volume, especially on smaller tanks where glass thickness is a larger proportion of total width.
• Mixing measurement units: Entering some dimensions in inches and others in centimeters produces nonsensical results. Use one unit system consistently and let the calculator handle conversions.
• Measuring overall length instead of the straight-section length:The formula subtracts the radius from the overall length automatically, so enter the tank's full end-to-end length as measured, not a pre-shortened straight-section length — subtracting the radius yourself before entering it will double-count the adjustment.
• Guessing the radius instead of measuring the curve's width:If you can't easily pinpoint where the curve begins, measure the width of the tank at the curved end and divide by two — a bullnose curve is typically a half-circle matching the tank's width, so this gives a reliable radius estimate.